Widening the Wheel Wells for 37-Inch Tires

Key Takeaways: Fitting 37-inch tires under a 60 Series Land Cruiser restoration without cutting corners means reshaping the fenders and quarter panels rather than bolting on flares or hacking the openings. Done correctly, the widened openings keep the truck’s original factory body lines, the lower door skins and rusted seams get addressed on the way, and the whole shell goes back to bare metal before a two-stage primer and a fresh coat of Toyota paint code 147 silver. It is fabrication-heavy work: the fender and quarter pieces curve in multiple directions and carry a body line, so every panel has to be hand-formed and welded in to match the factory shape.


A 60 Series Land Cruiser is one of the most rewarding platforms to build precisely because its body lines are so clean and recognizable. That also makes it unforgiving. When an owner wants to run 37-inch tires, the stock wheel openings simply aren’t wide enough, and the easy fixes — plastic flares, or cutting the openings and leaving raw edges — look wrong on a truck this iconic. The project below walks through a full bodywork-and-paint restoration where the wheel wells were widened, the sheet metal was rebuilt, and the shell was refinished in silver 147, all while preserving the factory character of the truck.

This is the kind of metal fabrication and restoration work handled at the shop: bare-metal teardowns, structural rust repair, hand-formed panels, and restoration-level paint. It is body and paint work, not mechanical, and it’s exactly where a truck like this belongs when the goal is a finish that looks factory-correct rather than modified.

What does it take to fit 37-inch tires on a 60 Series Land Cruiser restoration?

Clearing 37s is not a spacer-and-flare job on a truck you want to keep looking stock. The wheel openings have to physically grow — both the front fenders and the rear quarter panels — and the new, larger openings have to carry the same crisp body line the factory pressed into the steel. That means fabricating new fender and quarter sections from scratch, blending them into the existing panels, and rebuilding the inner fenders behind them so the wheel and tire have room to move through their full range.

The front fenders are the tightest area. There’s very little material ahead of the wheel before you run into the front of the fender, so the opening gets pushed as far forward as the panel will allow to buy maximum clearance. At the rear, the quarter openings move rearward and downward, which frees up room for the larger tire and lets the body sit right over it.

Why start with a full bare-metal strip and disassembly?

Before any fabrication begins, the truck comes apart. Doors, tailgate, and hatch all come off, and the body is stripped to bare metal. There are two reasons this matters. First, you can only trust metalwork when you can see every inch of the steel — hidden rust and old repairs stay hidden under paint and undercoating. Second, panels that will be reshaped or replaced are far easier to work when they’re isolated and accessible rather than fought around in place.

With the shell bare, the smaller but important jobs get done: the holes left in the rocker panels by factory trim are closed up, and the seam sealer in the roof gutters and around the windshield is removed so any rust underneath can be repaired and the seams resealed properly. These are the areas that quietly rot on 60 Series trucks, and catching them during a bare-metal restoration is far cheaper than revisiting them after paint.

How do you widen a 60 Series fender without losing the factory body line?

This is the hardest part of the entire project. A widened fender isn’t a flat add-on — the new sections curve in more than one direction and still have to carry the pressed body line that runs along the panel. Getting a hand-formed piece to pick up that line, hold the correct contour, and meet the existing fender cleanly is genuinely difficult metalwork.

The front of the fender is widened as far forward as the panel geometry allows, maximizing the opening. The fabricated pieces are shaped with the body line intact so that, once welded in and finished, the widened opening reads as if it left the factory that way. Behind them, new inner front and rear inner fenders are built to match the new opening shape. Those inner panels are organic, compound-curved parts with bends running in several directions, and they have to fit tightly to the fender and quarter lip — a fussy, time-consuming piece of the job that never shows in photos but determines whether everything lines up.

Fabricating the rear quarter panel wheel openings

The rear quarters were rebuilt using donor quarter panels. To push the wheel opening rearward, a small section — roughly the front three and a half inches of an original quarter — was grafted in to move the opening back. The lower portion of the quarter was removed for additional tire clearance, and while that area was open, the factory bumper indentation was deleted for a cleaner look.

Donor panels come with their own problems. Most of the donor steel had rust, so the corroded areas were cut out and new sections of the wheel-opening lip were fabricated to replace them. The result is a wheel opening that’s larger and correctly shaped, built from sound metal rather than patched-over rust.

Why the lower door skins always get replaced on 60 Series doors

On these trucks, the bottoms of the doors almost always hide rust. Water sits in the lower door and rots the skin from the inside, so the lower door skin sections are replaced as a matter of course during a proper restoration. The replacement lower skins are fabricated in-house rather than bought off the shelf, because the doors aren’t flat — they have a specific curvature, and a skin that isn’t formed to the right shape will look wrong once it’s on the truck.

Forming those skins takes real sheet-metal equipment: an english wheel to raise the crown, a brake for the bends, a bead roller, and a slip roller. When welding a new skin in, a removable backing brace is wedged in behind the seam. It has an aluminum face and a slight outward bulge so the panel can’t cave inward from weld heat, and it pulls right back out to move on to the next door.

Inner fenders, A-pillar gutters, and the details that don’t show

Alongside the visible panels, the A-pillar gutter sections were removed, cleaned, and replaced — another common 60 Series rust and grime area. Combined with the new inner fenders built to the widened opening shape, this is the unglamorous fabrication that makes the difference between a truck that looks good in photos and one that’s actually sound underneath.

What’s the right way to weld in fabricated panels?

The welding approach is chosen to keep the finished metal as flat and clean as possible. Panels are overlapped and then cut through both layers at roughly a 45-degree angle with a small saw blade, which creates a tight, matched butt joint. Those joints are then TIG welded without filler rod, so the two pieces fuse directly with minimal added material and minimal distortion — critical when the goal is a body-line-perfect finish with little filler.

TIG isn’t the only tool, though. Depending on the panel and the location of the weld, MIG is sometimes the better choice, and both get used across a project like this. Matching the process to the joint, rather than forcing one method everywhere, is part of what keeps the metalwork clean.

Primer, block sanding, and the 147 silver respray

Once the fabrication is complete, the truck moves into paint prep. It’s primed, block-sanded, and primed again — multiple rounds of primer and sanding are what make a widened, heavily fabricated body read as straight and factory-smooth. When the primer is right, the shell goes back into the booth for base and clear in Toyota paint code 147, a factory silver, tying the modified body back to an OEM color.

The finished truck

Reassembled and sitting on its 37-inch tires, the truck keeps the proportions and body lines of a stock 60 Series while carrying the tire size and stance the owner wanted. That’s the whole point of doing the work this way: the modification disappears into the design instead of fighting it.

Frequently Asked Questions: 60 Series Land Cruiser Restoration

Can you fit 37-inch tires on a 60 Series Land Cruiser restoration without cutting the body?

Not cleanly. Running 37s requires physically enlarging both the front fender and rear quarter wheel openings and rebuilding the inner fenders for clearance. The difference between a good result and a bad one is whether those enlarged openings are fabricated to keep the factory body line, rather than simply trimmed.

Why replace the lower door skins on a 60 Series instead of repairing them?

The bottoms of 60 Series doors almost always hide rust that has worked from the inside out. By the time it’s visible, the skin is usually compromised. Replacing the lower skin with a properly formed panel is more reliable than patching, and because the doors are curved, the replacement skin has to be shaped on an english wheel and related tooling to match.

What is Toyota paint code 147?

Toyota paint code 147 is a factory silver. Refinishing a modified body in an OEM code like 147 keeps the truck tied to an original Toyota color even after extensive fabrication, which is part of what makes the finished result look factory-correct rather than custom.

Why TIG weld panels without filler rod?

Cutting overlapped panels at an angle creates a tight, matched joint that can be fused directly. TIG welding it without filler rod adds minimal material and puts less distortion into the surrounding metal, which means less filler and a straighter finished panel — important on visible body panels that carry a body line.

Is this bodywork or mechanical work?

This is bodywork, fabrication, and paint: bare-metal teardown, structural rust repair, hand-formed panels, and restoration-level refinishing. It does not include mechanical work. For a 60 Series that needs its wheel openings widened, rust addressed, and a factory-correct respray, that fabrication-and-paint focus is exactly the right fit.


Thinking about a 60 Series Land Cruiser Restoraiton project like this? Wheel-well widening, rust repair, and a factory-correct respray are core restoration work — the kind of bare-metal fabrication and paint the shop specializes in. Reach out to talk through your truck.

Kelly Saad, owner of Restoration Sector

About the Author: Kelly Saad

Kelly Saad is the owner of Restoration Sector and has over 35 years of hands-on experience restoring classic vehicles. His work focuses exclusively on body restoration — structural rust repair, metal fabrication, and restoration-level paint preparation. Restoration Sector only paints vehicles restored in-house, ensuring long-term finish stability.

Read Kelly's Full Bio →

Classic vehicle body restoration work at Restoration Sector

Serious Restoration Starts at the Metal

Restoration Sector specializes exclusively in body restoration for classic vehicles — addressing rust, structural metal repair, fabrication, and restoration-level paint at the bare-metal level.

Vehicles are only painted after full in-house restoration work, ensuring finishes remain stable, durable, and true to the underlying structure.

Serving Arizona and nationwide clients via vehicle transport